CFZLR - SOLDER ALLOYS WITHOUT LEAD
- MSDS: CFZLR
- Manufacturer: KESTER SOLDER
- Product Name: SOLDER ALLOYS WITHOUT LEAD
- National Stock Number: 3439-00N055781
Product Identification
Product ID:SOLDER ALLOYS WITHOUT LEAD
MSDS Date:05/22/1996
FSC:3439
NIIN:00N055781
MSDS Number: CFZLR
Responsible Party
DES PLAINES, IL 60018
US
Emergency Phone: 800-424-9300(CHEMTREC)
Info Phone: 708-297-1600
Cage: GO345
Contractor
Telephone: 847-297-1600
Cage: 75297
Ingredients
INDIUM
CAS: 7440-74-6
RTECS: NL1050000
OSHA PEL 0.1 MG/M3
ACGIH TLV: 0.1 MG/M3
TIN
CAS: 7440-31-5
RTECS: XP7320000
OSHA PEL 2 MG/M3
ACGIH TLV: 2 MG/M3
SILVER (SARA 313) (CERCLA)
CAS: 7440-22-4
RTECS: VW3500000
OSHA PEL 0.01 MG/M3
ACGIH TLV: 0.1 MG/M3
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
BISMUTH
CAS: 7440-69-9
RTECS: EB2600000
OSHA PEL N/K
ACGIH TLV: N/K
ANTIMONY (SARA 313) (CERCLA)
CAS: 7440-36-0
RTECS: CC4025000
OSHA PEL 0.5 MG/M3
ACGIH TLV: 0.5 MG/M3 (SB)
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
COPPER (SARA 313) (CERCLA)
CAS: 7440-50-8
RTECS: GL5325000
OSHA PEL 0.1MG/M3 FUME;1 DUST
ACGIH TLV: 0.2 MG/M3 FUME
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PRIMARY EXPOSURE DURING SOLDERING IS
TO FLUX FUMES. ACUTE:SKIN CONTACT/ABSORPTION & EYE CONTACT:NONE.
INHALATION/INGESTION:NOT APPLICABLE. CHRONIC:NOT APPLICABLE. TARGET
ORGANS:NOT ESTABLISHED.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:NONE SPECIFIED BY MANUFACTURER.
Medical Cond Aggravated by Exposure:PRE-EXISTING CONDITIONS OF THE
LUNGS, DISEASES OF THE BLOOD & BLOOD-FORMING ORGANS, KIDNEYS,
NERVES & POSSIBLY REPRODUCTIVE SYSTEM.
First Aid
First Aid:SEEK MEDICAL ASSISTANCE FOR FURTHER TREATMENT, OBSERVATION &
SUPPORT IF NEEDED. INGEST:CALL MD IMMEDIATELY . INHAL:REMOVE TO
FRESH AIR. SUPPORT BREATHING (GIVE O*2/ARTF RESP) . EYES:FOR BU RNS
FLUSH IMMEDIATELY W/COOL WATER FOR AT LEAST 15 MINUTES. SKIN:FOR
BURNS FLUSH IMMEDIATELY W/COOL WATER.
Fire Fighting
Flash Point Method:TOC
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:FLUX IN CORED SOLDER MAY IGNITE WHEN
SOLDER MELTS IN FIRE.
Accidental Release
Spill Release Procedures:MELTED SOLDER WILL SOLIDIFY ON COOLING & CAN
BE SCRAPED UP. USE CAUTION TO AVOID BREATHING FUMES IF GAS TORCH IS
USED TO CUT UP LARGE PIECES.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE AWAY FROM SOURCES OF SULFUR.
AVOID BREATHING FUMES DURING SOLDERING. DO NOT PLACE FLUX CORED
SOLDER INTO HOT SOLDER POT BECAUSE FLUX MAY IGNITE.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Exposure Controls
Respiratory Protection:USUALLY NOT REQUIRED. WHEN VENTILATION IS NOT
SUFFICIENT TO REMOVE FUMES FROM BREATHING ZONE, A NIOSH APPROVED
CARTRIDGE TYPE RESPIRATOR SHOULD BE WORN.
Ventilation:PROVIDE ADEQUATE EXHAUST VENTILATION (GENERAL &/OR LOCAL TO
MEET TLV REQUIREMENTS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
Spec Gravity:>1 (H*2O=1)
Solubility in Water:0% BY WT
Appearance and Odor:SILVER-GRAY METAL IN BAR, WIRE, RIBBON OR PREFORMED
SHAPES.
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ACID, STRONG OXIDIZERS.
Stability Condition to Avoid:NONE.
Hazardous Decomposition Products:SOLDER CONTAINING ANTIMONY MAY
LIBERATE ANTIMONY OXIDE IF HEATED ABOVE 1000F.
Disposal
Waste Disposal Methods:DISPOSAL MUST BE I/A/W FEDERAL, STATE & LOCAL
REGULATIONS . SOLDER CAN BE RECLAIMED. CAUTION:EMPTY CONTAINERS MAY
CONTAIN PRODUCT RESIDUE. OBSERVE ALL LABEL PRECAUTIONS.
Other Information
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.